Oracle X7-8 Service Manual Download Page 102

Page: 102 / 308

Preparing the Server for Component Replacement

■

Power supplies

“Servicing Power Supplies (CRU)” on page 138

■

Dual PCIe Card Carriers (DPCCs)

“Servicing PCIe Cards and Carriers

(CRU)” on page 148

See

“Prepare the Server for Hot Service (Oracle ILOM CLI)” on page 103

“Prepare the

Server for Hot Service (Oracle ILOM Web Interface)” on page 104

Warm service

Warm service

components can be serviced while the server is in Standby power mode. You can

remove and replace CMODs, DIMMs, and processors and heatsinks without disconnecting the

back panel AC power cords or shutting down Oracle ILOM.

The following components can be warm-serviced:

■

CMOD assembly

“Servicing CPU Module (CMOD) Components (FRU)” on page 160

■

Processor (CPU)

“Servicing Processors” on page 170

■

DIMM memory

“Servicing DIMMs” on page 182

See

“Prepare the Server for Warm Service (Oracle ILOM CLI)” on page 105

“Prepare the

Server for Warm Service (Oracle ILOM Web Interface)” on page 107

Cold service

Cold service

components must be serviced when the server is completely powered off and all

four AC power cords are disconnected from the server back panel AC power block.

The following components can be cold-serviced:

■

System module (SMOD)

“Servicing System Module (SMOD) Components

(FRU)” on page 195

■

Host bus adapter (HBA) card

“Servicing the Host Bus Adapter (HBA)

Card” on page 200

■

HBA cable

“Servicing the SAS Cable” on page 211

■

Energy Storage Module (ESM)

“Servicing the Energy Storage Module and

Cables” on page 206

■

Energy Storage Module cable

“Servicing the Energy Storage Module and

Cables” on page 206

■

System Clock Battery

“Replace the System Battery” on page 216

102

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands

Oracle X7-8, Service Manual

Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands