manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 141

Remove a Power Supply

Call Out

Description

1

AC3 System A (SMOD0)

2

AC2 System A (SMOD0)

3

AC1 System B (SMOD1)

4

AC0 System B (SMOD1)

Remove a Power Supply

You might need to remove power supplies to replace a PS or to access the release latch for the

front indicator module (FIM).

1.

Prepare the server for service. Choose one of the following methods:

■

Prepare the server for hot service.

■

Prepare the server for cold service.

See 

“Preparing the Server for Component Replacement” on page 101

.

2.

Identify the power supply that requires removal.

Access this component directly from the front of the server.
The following status indicators (LEDs) are lit when a power supply fault is detected:

■

Front and back Fault-Service Required LEDs

■

Amber Fault-Service Required LED on the faulty power supply

Servicing Components

141

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands