manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 35

System Module (SMOD) Overview

■

Oracle ILOM

■

Dual Oracle ILOM image

■

Signed Oracle ILOM image

■

512 MB DDR4 memory

■

128 MB of flash memory

■

1 GB of NAND memory

■

Baseboard management controller (BMC)

■

One RJ-45 serial management port (SER MGT).

■

One network management port, 1 Gbps (NET MGT).

■

One USB 3.0 port external on each SMOD.

■

Four 10GBase-T ports per SMOD (NET0-3).

■

Four hot swap capable disk drive bays. Four SAS3 storage drive bays 0-7.

■

Four drives in each SMOD. SMOD0 0-3 and SMOD1 0-3. Drives can be a total of eight

2.5-inch, hot-swappable SAS3 hard disk drives (HDDs) or eight 2.5-inch SAS3 solid state

drives (SSDs).

Two SMODs are accessible from the back panel of the server. The following illustration shows

SMODs and removal and installation levers with green lock release tabs.

About the Oracle Server X7-8

35

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands