Oracle X7-8 Service Manual Download Page 29

Page: 29 / 308

CPU Module (CMOD) Overview

Related Information

■

“Product Description” on page 17

■

“Servicing CPU Module (CMOD) Components (FRU)” on page 160

■

“CMOD Population Rules” on page 161

■

“System Module (SMOD) Overview” on page 34

CMOD Components

CMODs include the following processors (CPUs) and DIMM memory components:

■

Processor Heatsink Module (PHM) assembly includes heatsink, processor, TIM, carrier.

“CMOD Processor” on page 30

■

12 DIMM slots arranged in two groups of six

“CMOD Memory” on page 31

■

Fault Remind Test Circuit, which helps you locate failed DIMMs and verify a failed CPU

■

Fault Remind button

■

12 DIMM slot fault indicators

■

1 CPU fault indicator

The following illustration shows CMOD component locations.

About the Oracle Server X7-8

Summary of Contents for X7-8





















































































































































































































































































































Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands

Oracle X7-8, Service Manual

Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands