manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 205

Install the HBA Card

b.   

Rotate the thumbscrew in so it tucks inside the SMOD frame and does not

extend out.

6.

Ensure that the cables pass through the cable guides on the edge of the SMOD

(4).

7.

Connect the ESM extension cable to the connector on the HBA.

8.

Install the storage drives. See 

“Install a Storage Drive” on page 127

.

9.

Install the SMOD. See 

“Install an SMOD” on page 197

.

10.

Prepare the server for operation. See 

“Returning the Server to

Operation” on page 237

.

11.

Clear any related component faults. For more information see 

“Clear Hardware

Fault Messages (Oracle ILOM)” on page 53

.

Related Information

■

“Install an SMOD” on page 197

Servicing Components

205

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands