manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 161

Servicing CPU Module (CMOD) Components (FRU)

Call Out

Description

0

CMOD 0, SMOD0 System A

1

CMOD 1, SMOD0 System A

2

CMOD 2, SMOD0 System A

3

CMOD 3, SMOD0 System A

4

CMOD 4, SMOD1 System B

5

CMOD 5, SMOD1 System B

6

CMOD 6, SMOD1 System B

7

CMOD 7, SMOD1 System B

CMOD Population Rules

The Oracle Server X7-8 supports four and eight CMOD configurations. Each CMOD supports a

single socket containing a single processor. Each CMOD contains one Intel Xeon vx processor

28-core (shelf 4) processor.

For the single 4 socket server configuration:

■

System module 0 (SMOD0) System A and SMOD1 System B must be installed but only

SMOD0 is active.

■

CPU modules (CMODs) must be installed in slots 0-3. CMOD slots 4-7 are empty.

■

All eight DPCC slots 0-7 must be installed but only DPCC slots 0-3 are active.

■

All eight fan modules (FMs) must be installed but only FMs 0-3 are active.

Servicing Components

161

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands