manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 252

Configure UEFI Driver Settings

4.

On the Internal Devices screen, select the internal device or add In card slot that

you want to configure.

5.

On the PCI-E UEFI Driver Enable screen, select 

PCI-E UEFI Driver Enable

 and

press Enter. Do one of the following:

■

Select 

Enabled

 to enable the PCI-E UEFI Driver setting.

■

Select 

Disabled

 to disable the PCI-E UEFI Driver setting.

6.

Press the F10 key to save the changes and exit the BIOS Setup Utility.

Related Information

■

“Accessing the BIOS Setup Utility” on page 239

■

“BIOS Setup Utility Menu Options” on page 269

■

“Exit BIOS Setup Utility” on page 267

252

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands