manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 42

System Module (SMOD) Overview

The chassis internal components include:

Call

Out

Component

Description

Links

1

Top Cover

This component is part of the chassis and non-

replaceable.

“Replace the Midplane

Assembly” on page 226

.

2

Midplane/

busbar

The midplane assembly provides an interconnect

between the back panel components and the front panel

components. This component requires cold service.

“Replace the Midplane

Assembly” on page 226

.

3

CPU module

(CMOD) bays

Chassis CMOD bays can support either four or eight

CMODs. Servicing CMODs requires warm or cold

service.

“CPU Module (CMOD)

Overview” on page 28

.

“Servicing CPU Module

(CMOD) Components

(FRU)” on page 160

Chassis Front Panel Components

The following figure shows the server chassis front panel accessible replaceable components.

42

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands