manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 214

Install an Internal USB Drive

The USB flash drive is located inside the SMOD next to the HBA card.

7.

To remove a USB drive, pull it out of its slot.

Related Information

■

“Install an SMOD” on page 197

Install an Internal USB Drive

Perform this procedure to access and install internal USB flash drives when instructed by

service personnel.This is an internal component accessible from the back of the server by

removing SMOD0 and SMOD1.

1.

Prepare the server for cold service.

This is a cold-service component. Power down the system and disconnect the AC power cables

from the server before performing this procedure.
See 

“Preparing the Server for Component Replacement” on page 101

.

2.

Remove the SMOD. See 

“Remove an SMOD” on page 195

.

214

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands