manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 215

Install an Internal USB Drive

3.

Set the SMOD on a flat surface with the front side facing toward you.

4.

Close the SMOD handles.

5.

Rotate the SMOD 180 degrees so the back (connector) side is facing toward you.

6.

Turn the SMOD upside down and locate the HBA card.

Note - 

The connector (back) side of the SMOD should still be facing you.

The internal USB flash drive port is located inside SMOD0 or SMOD1 next to the HBA card.

7.

Insert the drive into the USB slot.

8.

Install the SMOD. See 

“Install an SMOD” on page 197

.

9.

Repeat these steps for another SMOD as required.

10.

Prepare the server for operation. See 

“Returning the Server to

Operation” on page 237

.

Related Information

■

“Install an SMOD” on page 197

Servicing Components

215

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands