manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 133

Install a Fan Module

Caution - 

Electrical hazard. During a hot-service procedure, voltage is present. Do not reach

into the vacant fan module slot with your hand or any object. Do not touch the exposed CMOD

fan module power connector.

When the fan is removed from the slot, a hinged air vane drops down to close the slot. The vane

maintains system cooling and prevents a disruption of server airflow during hot service.

Caution - 

Server overtemperature. The slot's air vane maintains system cooling by preventing a

disruption of server airflow. Do not open the air vane when the system is running.

Related Information

■

“Remove a Fan Frame” on page 136

■

“Install a Fan Module” on page 133

Install a Fan Module

Use this procedure after removing a fan module to install a replacement fan module or to install

a fan module after accessing the CMODs behind it.

Servicing Components

133

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands