manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 164

Remove the CMOD Cover

8.

Use the lever to slide the CMOD partially out of the server until you can grab it

with two hands.

Caution - 

The CMOD is heavy. Be prepared to hold it firmly when it is clear of the slot.

9.

To remove the CMOD, slide it completely out of the server.

Related Information

■

“Identify and Remove a Faulty DIMM” on page 189

■

“Identify and Remove a Faulty Processor” on page 171

■

“Install a CMOD” on page 167

Remove the CMOD Cover

When removing or installing the CMOD cover, always maintain component serviceability

requirements with regard to static protection.

1.

“Remove a CMOD” on page 162

164

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands