Oracle X7-8 Service Manual Download Page 90

Page: 90 / 308

Attach Devices to the Server

Attach Devices to the Server

This section provides instructions for connecting remote and local devices to the server so you

can interact with the service processor (SP) and the server console.

For port and connector information, see

“Back Panel Components” on page 21

Connect an Ethernet cable to the Gigabit Ethernet (NET) connectors as needed

for OS support.

To connect to Oracle ILOM over the network, connect an Ethernet cable to the

Ethernet port labeled NET MGT.

To access the Oracle ILOM command-line interface (CLI) locally using the

management port, connect a serial null modem cable to the RJ-45 serial port

labeled SER MGT.

Back Panel Connector Locations

The following illustration shows and describes the locations of the back panel connectors. Use

this information to set up the server, so that you can access diagnostic tools and manage the

server during service.

The following figure shows the locations of the server back panel connectors and ports.

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands

Oracle X7-8, Service Manual

Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands