manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 184

Install a Processor

DIMM Slot Numbering and Color Coding

Each CMOD contains 12 DIMM slots arranged in two groups of six slots. Each group of slots

is controlled by one of the four memory buffers. Each buffer has two independent memory

channels, Ch A and Ch B (six memory channels per CMOD). Each channel supports 1-6

DIMMs and has six assigned DIMM slots.

Channels 0, 1, and 2 are located on one side of the processor, and channels 3, 4 and 5 are on the

other side of the processor. To differentiate the two memory channels within a group of slots,

and to assist in DIMM population order, the six DIMM slots assigned to each channel have

color-coded slots and levers. The color-coding is black slots with black levers, and white slots

with white levers.

For slot numbering information see 

“Identifying Components” on page 24

.

Related Information

■

“DIMM and Processor Physical Layout” on page 183

■

“DIMM Population Scenarios” on page 184

■

“DIMM Population Rules” on page 185

■

“DIMM Operating Speeds” on page 188

■

“DIMM Rank Classification Labels” on page 188

■

“Inconsistencies Between DIMM Fault Indicators and the BIOS Isolation of Faulty

DIMMs” on page 188

DIMM Population Scenarios

There are two scenarios in which you are required to populate DIMMs:

■

A DIMM fails and needs to be replaced.
In this scenario, you can use the Fault Remind button to determine the failed DIMM, then

remove the failed DIMM and replace it. To ensure that system performance is maintained,

you must replace the failed DIMM with a DIMM of the same size (in gigabytes) and type

(64-GB quad-rank (QR) Load-Reduced DIMMs (LRDIMMs) and 32-GB dual-rank (DR)

and 16-GB DR Registered DIMMs (RDIMMs). In this scenario, you should not change the

DIMM configuration.

■

You have purchased new DIMMs and you want to use them to upgrade the server's memory.
In this scenario, you should adhere to DIMM population rules and follow the recommended

DIMM population order for optimal system performance.

184

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands