manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 183

Install a Processor

The following topics and procedures provide information to assist you when replacing a DIMM

or upgrading DIMMs:

■

“DIMM and Processor Physical Layout” on page 183
“DIMM Population Scenarios” on page 184
“DIMM Population Rules” on page 185
“DIMM Rank Classification Labels” on page 188

■

“Inconsistencies Between DIMM Fault Indicators and the BIOS Isolation of Faulty

DIMMs” on page 188

■

“Identify and Remove a Faulty DIMM” on page 189

■

“Identify and Remove a Faulty DIMM” on page 189

■

“Install a DIMM” on page 192

For component serviceability, locations, and designations, see 

“Identifying

Components” on page 24

.

DIMM and Processor Physical Layout

The physical layout of the CMOD memory DIMMs and processor is shown in the following

figure.

Servicing Components

183

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands