Oracle X7-8 Service Manual Download Page 192

Page: 192 / 308

Install a DIMM

Related Information

■

“DIMM and Processor Physical Layout” on page 183

■

“DIMM Population Rules” on page 185

■

“Install a DIMM” on page 192

Install a DIMM

Use this procedure to install DIMMs for a memory upgrade or a configuration change or as part

of a DIMM reset (removal and installation).

Unpack the replacement DDR4 DIMM and place it on an antistatic mat.

Ensure that the replacement DDR4 DIMM matches the size of the DIMM it is

replacing.

You must not replace a dual-rank DIMM with a quad-rank DIMM and vice versa. If you

violate this rule, the performance of the server might be adversely affected. For DIMM socket

population rules, see

“DIMM Population Rules” on page 185

Prepare the server for service. Choose one of the following methods:

■

Prepare the server for warm service.

■

Prepare the server for cold service.

See

“Preparing the Server for Component Replacement” on page 101

Access DIMMs as required.

■

Remove the CMOD. See

“Remove a CMOD” on page 162

■

Remove the CMOD top cover. See

“Remove the CMOD

Cover” on page 164

To remove the CMOD top cover, push the release button, slide the CMOD cover toward

the back of the CMOD, and lift it away.

■

Remove DIMMs. See

“Identify and Remove a Faulty DIMM” on page 189

Note -

If you are changing or adding DIMMs as part of an upgrade, ignore the fault

identification instructions.

192

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands

Oracle X7-8, Service Manual

Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands