Oracle X7-8 Service Manual Download Page 115

Page: 115 / 308

Power Down the Server for Immediate Shutdown (Oracle ILOM CLI)

■

“Power Down the Server for Immediate Shutdown (Oracle ILOM Web

Interface)” on page 116

■

“Power On the Server” on page 238

Power Down the Server for Immediate Shutdown

(Oracle ILOM CLI)

Caution -

This procedure quickly forces the server Main power off. You might corrupt your

system data during an immediate power-down, so use this procedure to power down the server

only after attempting the graceful power-down procedure.

Log in to the Oracle ILOM command-line interface (CLI) using an Administrator

account.

Oracle ILOM displays the default command prompt (

), indicating that you have successfully

logged in to Oracle ILOM.

From the CLI prompt, type the following command:

stop -f /System

The server powers down immediately.

Disconnect the power and data cables from the server.

See

“Remove Power” on page 119

Caution -

When you power down the server using Oracle ILOM, the server enters Standby

power mode. Power is still directed to the service processor remote management subsystem and

power supply fans. To completely power off the server, you must disconnect the power cords

from the power supplies.

Related Information

■

“Power Down the Server for Immediate Shutdown” on page 116

■

“Power Down the Server for Immediate Shutdown (Oracle ILOM Web

Interface)” on page 116

■

“Power On the Server” on page 238

Preparing for Service

115

Summary of Contents for X7-8





















































































































































































































































































































Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands

Oracle X7-8, Service Manual

Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands