manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 176

Identify and Remove a Faulty Processor

d.   

Remove the processor carrier with processor from the heatsink by prying or

pinching the plastic latch tabs that attach the processor to the heatsink.

Note - 

A thin layer of thermal grease separates the heatsink and the processor. This grease

acts as an adhesive. Do not allow the thermal grease to contaminate the work space or other

components.

6.

If you plan on reusing either the heatsink or processor, use an alcohol pad to

clean the thermal grease on the underside of the heatsink and on the top of the

processor.

Caution - 

Failure to clean thermal grease from the heatsink could result in the accidental

contamination of the processor socket or other components. Also, be careful not to get the

grease on your fingers, as this could result in contamination of components.

Related Information

■

“Install a Processor” on page 177

176

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands