Oracle X7-8 Service Manual Download Page 239

Page: 239 / 308

Setting Up BIOS Configuration Parameters

This section provides an overview of BIOS configuration management, UEFI BIOS, and the

BIOS Setup Utility:

■

“Manage the BIOS Configuration” on page 239

■

“Accessing the BIOS Setup Utility” on page 239

■

“Using UEFI BIOS” on page 244

■

“Common BIOS Setup Utility Tasks” on page 245

Related Information

■

“BIOS Setup Utility Menu Options” on page 269

Manage the BIOS Configuration

The BIOS configuration parameters on an Oracle x86 server are manageable from the BIOS

Setup Utility and Oracle ILOM. For information about using these tools to manage the BIOS

configuration, refer to:

■

Oracle ILOM

– “Maintaining x86 BIOS Configuration Parameters” in the

Oracle ILOM

Administrator's Guide for Configuration and Maintenance Firmware Release 4.0

in the

Oracle Integrated Lights Out Manager (ILOM) 4.0 Documentation Library at

http://www.

oracle.com/goto/ilom/docs

■

BIOS Setup Utility

–

“Common BIOS Setup Utility Tasks” on page 245

Accessing the BIOS Setup Utility

The BIOS Setup Utility provides five main menus that you can use to view product information,

and to configure, enable, and disable, or manage system components.

Setting Up BIOS Configuration Parameters

239

Summary of Contents for X7-8





















































































































































































































































































































Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands

Oracle X7-8, Service Manual

Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands