manualshive.com logo in svg

Oracle X7-8, Service Manual

Share
Download
Oracle X7-8 Service Manual Download Page 216

Replace the System Battery

Replace the System Battery

Perform this procedure to replace a failed system battery (also known as an RTC battery). The

Real Time Clock system battery type is 3V Lithium Coin Cell Battery CR 2032.

This is an internal component accessed from the back of the server by removing the SMOD.

For component serviceability, locations, and designations, see 

“Identifying

Components” on page 24

.

1.

Prepare the server for cold service.

This is a cold-service component. Power down the system and disconnect the AC power cables

from the server before performing this procedure.
See 

“Preparing the Server for Component Replacement” on page 101

.

2.

Remove the SMOD. See 

“Remove an SMOD” on page 195

.

3.

Set the SMOD on a flat surface with the back side facing toward you.

The system battery is located on the SMOD motherboard.

4.

To remove the battery, pull it up and out of its holder.

216

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands