manualshive.com logo in svg

Micronas SDA 6000, User Manual

Share
Download
Micronas SDA 6000 User Manual Download Page 207

SDA 6000 

PRELIMINARY DATA SHEET

Version 2.1

Peripherals

7 - 49

Micronas

 

Figure 7-23

ASC Register Overview

The ASC0 supports full-duplex asynchronous communication up to

 2.08 

MBaud and

half-duplex synchronous communication up to

 4.16

 MBaud (@ 33.33 MHz CPU clock).

In synchronous mode, data is transmitted or received synchronous to a shift clock which
is generated by the microcontroller. In asynchronous mode, 8- or 9-bit data transfer,
parity generation, and the number of stop bits can be selected. Parity, framing, and
overrun error detection is provided to increase the reliability of data transfers.
Transmission and reception of data is double-buffered. For multiprocessor
communication, a mechanism to distinguish address from data bytes is included. Testing
is supported by a loop-back option. A 13-bit baud rate timer with a versatile input clock
divider circuitry provides the ASC0 with the serial clock signal. In a special asynchronous
mode, the ASC0 supports IrDA data transmission up to 115.2 KBaud with fixed or
programmable IrDA pulse width.

A transmission is started by writing to the Transmit Buffer register S0TBUF (by way of
an instruction or a PEC data transfer). Only the number of data bits which is determined
by the selected operating mode, will actually be transmitted, e.g. bits written to positions
9 through 15 of register S0TBUF are always insignificant.
Data transmission is double-buffered, so a new character may be written to the transmit
buffer register, before the transmission of the previous character is complete. This allows
the transmission of characters back-to-back without gaps.

ASC0 Receive Interrupt Control Register

ASC0 Receive Buffer Register (read only)

ASC0 IrDA Pulse Mode and Width Register

UEA11142

Port 3 Open Drain Control Register
Port 3 Direction Control Register
ASC0 Baud Rate Generator/Reload Register
ASC0 Transmit Buffer Register
ASC0 Transmit Interrupt Control Register
ASC0 Transmit Buffer Interrupt Control Register

Autobaud Status Register

Autobaud Control Register

S0TBIC

ABSTAT

ABCON

ODP3

S0BG
S0TBUF
S0TIC

DP3

S0RIC
S0EIC

S0FDV
S0PMW
S0RBUF

S0CON

P3

ASC0 Error Interrupt Control Register

ASC0 Fractional Divider Regiser

ASC0 Control Register

Port 3 Data Register

P3

ODP3

TxD0/P3.10

RxD0/P3.11

DP3

Ports & Direction Control
Alternate Functions

Control Registers

Data Registers

S0TBUF

S0RBUF

S0BG

S0PMW

ABSTAT

ABCON

S0CON

S0FDV

S0TBIC

S0RIC

S0EIC

S0TIC

Interrupt Control

Summary of Contents for SDA 6000





























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands