manualshive.com logo in svg

Freescale Semiconductor MCF54455, Reference Manual

Share
Download
Freescale Semiconductor MCF54455 Reference Manual Download Page 903

Debug Module

34-61

Freescale Semiconductor

Table 34-33

 shows the PSTDDATA specification for multiply-accumulate instructions.

1

During normal exception processing, the PSTDDATA output is driven to a 0xCC indicating the exception processing state. 
The exception stack write operands, as well as the vector read and target address of the exception handler may also be 
displayed.

Exception Processing:

PSTDDATA = 0xCC, 
{0xB,destination},

// stack frame

{0xB,destination},

// stack frame

{0xB,source},

// vector read

PSTDDATA = 0x5,{[0x9AB],target}

// handler PC

The PSTDDATA specification for the reset exception is shown below:

Exception Processing:

PSTDDATA = 0xCC, 
PSTDDATA = 0x5,{[0x9AB],target}

// handler PC

The initial references at address 0 and 4 are never captured nor displayed because these accesses are treated as 
instruction fetches.

For all types of exception processing, the PSTDDATA = 0xCC value is driven at all times, unless the PSTDDATA output 
is needed for one of the optional marker values or for the taken branch indicator (0x5).

2

For JMP and JSR instructions, the optional target instruction address is displayed only for those effective address fields 
defining variant

 

addressing modes. This includes the following <ea>x values: (An), (d16,An), (d8,An,Xi), (d8,PC,Xi).

3

For move multiple instructions (MOVEM), the processor automatically generates line-sized transfers if the operand 
address reaches a 0-modulo-16 boundary and there are four or more registers to be transferred. For these line-sized 
transfers, the operand data is never captured nor displayed, regardless of the CSR value. 
The automatic line-sized burst transfers are provided to maximize performance during these sequential memory access 
operations.

Table 34-33. PSTDDATA Values for User-Mode Multiply-Accumulate Instructions

Instruction

Operand Syntax

PSTDDATA Nibble

mac.l

Ry,Rx,ACCx

PSTDDATA = 0x1

mac.l

Ry,Rx,<ea>y,Rw,ACCx

PSTDDATA = 0x1, {0xB, source operand}

mac.w

Ry,Rx,ACCx

PSTDDATA = 0x1

mac.w

Ry,Rx,ea,Rw,ACCx

PSTDDATA = 0x1, {0xB, source operand}

move.l

{Ry,#<data>},ACC

x

 PSTDDATA = 0x1

move.l

{Ry,#<data>},MACSR

PSTDDATA = 0x1

move.l

{Ry,#<data>},MASK PSTDDATA = 0x1

move.l

{Ry,#<data>},ACCext01

PSTDDATA = 0x1

move.l

{Ry,#<data>},ACCext23

PSTDDATA = 0x1

move.l

ACCext01,Rx PSTDDATA = 0x1

move.l

ACCext23,Rx PSTDDATA = 0x1

move.l

ACCy,ACCx PSTDDATA = 0x1

move.l

ACCy,Rx PSTDDATA = 0x1

move.l

MACSR,CCR PSTDDATA = 0x1

move.l

MACSR,Rx PSTDDATA = 0x1

Summary of Contents for MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands