manualshive.com logo in svg

Freescale Semiconductor MCF54455, Reference Manual

Share
Download
Freescale Semiconductor MCF54455 Reference Manual Download Page 457

FlexBus

20-4

Freescale Semiconductor

Because this device shares the FlexBus signals with the PCI controller, this signal tristates between bus 
cycles.

20.2.5

Read/Write (FB_R/W)

The processor drives the FB_R/W signal to indicate the current bus operation direction. It is driven high 
during read bus cycles and low during write bus cycles.

Because this device shares the FlexBus signals with the PCI controller, this signal tristates between bus 
cycles.

20.2.6

Address Latch Enable (FB_ALE)

The assertion of FB_ALE indicates that the device has begun a bus transaction and the address and 
attributes are valid. FB_ALE is asserted for one bus clock cycle. FB_ALE may be used externally to 
capture the bus transfer address (

Figure 20-7

).

Because this device shares the FlexBus signals with the PCI controller, this signal tristates between bus 
cycles.

20.2.7

Transfer Size (FB_TSIZ[1:0])

For memory accesses, these signals, along with FB_TBST, indicate the data transfer size of the current bus 
operation. The interface supports byte, word, and longword operand transfers and allows accesses to 8-, 
16-, and 32-bit data ports.

For misaligned transfers, FB_TSIZ[1:0] indicates the size of each transfer. For example, if a longword 
access through a 32-bit port device occurs at a misaligned offset of 0x1, a byte is transferred first 
(FB_TSIZ[1:0] = 01), a word is transferred next at offset 0x2 (FB_TSIZ[1:0] = 10), and the final byte is 
transferred at offset 0x4 (FB_TSIZ[1:0] = 01).

For aligned transfers larger than the port size, FB_TSIZ[1:0] behaves as follows:

•

If bursting is used, FB_TSIZ[1:0] is driven to the transfer size.

•

If bursting is inhibited, FB_TSIZ[1:0] first shows the entire transfer size and then shows the port 
size.

For burst-inhibited transfers, FB_TSIZ[1:0] changes with each FB_TS assertion to reflect the next transfer 
size. For transfers to port sizes smaller than the transfer size, FB_TSIZ[1:0] indicates the size of the entire 
transfer on the first access and the size of the current port transfer on subsequent transfers. For example, 

Table 20-2. Data Transfer Size

FB_TSIZ[1:0]

Transfer Size

00

4 bytes (longword)

01

1 byte

10

2 bytes (word)

11

16 bytes (line)

Summary of Contents for MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands