manualshive.com logo in svg

Freescale Semiconductor MCF54455, Reference Manual

Share
Download
Freescale Semiconductor MCF54455 Reference Manual Download Page 490

SDRAM Controller (SDRAMC)

Freescale Semiconductor

21-3

•

Supports up to 512 MByte of memory.
— 25 bits RA+CA, 2 bits BA, 16-bit bus, two chip selects

•

Supports page mode for decreased latency and higher bandwidth; remembers one active row for 
each bank; four independent active rows per each chip select

•

Programmable refresh interval timer

•

Supports sleep mode and self-refresh mode

•

Error detect and parity check are not supported

•

The SDRAM controller does not include a dedicated I

2

C interface to access memory module 

(DIMM) serial presence detect EEPROM. If needed, this must be managed by one of the on-chip 
I

2

C channels external to the SDRAM controller.

•

Read clock recovery block

21.1.3

Terminology

The following terminology is used in this chapter:

•

SDRAM block: Any group of DRAM memories selected by one of the SD_CS signals. Therefore, 
the SDRAMC can support up to two independent memory blocks. The base address of each block 
is programmed in the SDRAM chip-select configuration registers. 

•

SDRAM bank: An internal partition in an SDRAM device. For example, a 64-Mbit SDRAM 
component might be configured as four 512K x 32 banks. Banks are selected through the 
SD_BA[1:0] signals.

•

SDRAM: RAMs that operate like asynchronous DRAMs but with a synchronous clock, a 
pipelined, multiple-bank architecture, and a faster speed. 

21.2

External Signal Description

This section introduces the signal names used in this chapter.

Table 21-1. SDRAM Interface—Detailed Signal Descriptions

Signal

I/O

Description

SD_A[13:0]

O

Memory multiplexed row/column address. Provides the row address for 

ACTV

 commands, and the column 

address and auto-precharge bit for 

READ

/

WRITE

 commands, to select one location out of the memory array 

in the respective bank. A10 is sampled during a precharge command to determine whether the precharge 
applies to one bank (A10 negated) or all banks (A10 asserted). If only one bank is to be precharged, the 
bank is selected by SD_BA[1:0].
The address outputs also provide the opcode during a MODE REGISTER SET command. SD_BA[1:0] 
signals define which mode register is loaded during the MODE REGISTER SET (MRS or EMRS). A12 is 
used on device densities of 256 Mb and above.

Timing

Assertion/Negation — Occurs synchronously with SD_CLK

SD_BA[1:0]

O

Memory bank address. Define which bank an 

ACTV

, 

READ

, 

WRITE

, or PRECHARGE command is being 

applied. It is also used to select the SDRAM internal mode register during power-up initialization.

Timing

Assertion/Negation — Occurs synchronously with SD_CLK

Summary of Contents for MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands