manualshive.com logo in svg

Freescale Semiconductor MCF54455, Reference Manual

Share
Download
Freescale Semiconductor MCF54455 Reference Manual Download Page 236

Universal Serial Bus Interface – On-The-Go Module

Freescale Semiconductor

10-29

10.3.4.10 Master Interface Data Burst Size Register (BURSTSIZE)

This register is not defined in the EHCI specification. BURSTSIZE dynamically controls the burst size 
during data movement on the initiator (master) interface.

10.3.4.11 Transmit FIFO Tuning Control Register (TXFILLTUNING)

This register is not defined in the EHCI specification. The TXFILLTUNING register controls performance 
tuning associated with how the module posts data to the TX latency FIFO before moving the data onto the 
USB bus. The specific areas of performance include how much data to post into the FIFO and an estimate 
for how long that operation takes in the target system.

Definitions:

T

0

 = Standard packet overhead

T

1

 = Time to send data payload

T

s

 = Total packet flight time (send-only) packet (

T

s

 = 

T

0

 + 

T

1

)

T

ff

 = Time to fetch packet into TX FIFO up to specified level

T

p

 = Total packet time (fetch and send) packet (

T

p

 = 

T

ff

 + 

T

s

)

Table 10-28. TTCTRL Field Descriptions

Field

Description

31

Reserved, must be cleared.

30–24

TTHA

TT Hub Address. This field is used to match against the Hub Address field in a QH or siTD to determine if the 
packet is routed to the internal TT for directly attached FS/LS devices. If the hub address in the QH or siTD 
does not match this address then the packet is broadcast on the high speed ports destined for a downstream 
HS hub with the address in the QH or siTD.

23–0

Reserved, must be cleared.

Address: 0xFC0B_0160 (BURSTSIZE)

Access: User read/write

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

R 0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

TXPBURST

RXPBURST

W

Reset 0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

1

0

0

0

0

0

0

0

1

0

0

Figure 10-26. Master Interface Data Burst Size (BURSTSIZE)

Table 10-29. BURSTSIZE Field Descriptions

Field

Description

31–16

Reserved, must be cleared.

15–8

TXPBURST

Programable TX burst length. Represents the maximum length of a burst in 32-bit words while moving data from 
system memory to the USB bus. Must not be set to greater than 16.

7–0

RXPBURST

Programable RX burst length. This register represents the maximum length of a burst in 32-bit words while 
moving data from the USB bus to system memory. Must not be set to greater than 16.

Summary of Contents for MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands