manualshive.com logo in svg

Freescale Semiconductor MCF54455, Reference Manual

Share
Download
Freescale Semiconductor MCF54455 Reference Manual Download Page 760

DMA Serial Peripheral Interface (DSPI)

Freescale Semiconductor

31-7

25

PCSSE

Peripheral chip select strobe enable. Selects between the DSPI_PCS5 and DSPI_PCSS functions on the 
DSPI_PCS5/PCSS signal. See 

Section 31.4.3.5, “Peripheral Chip Select Strobe Enable (PCSS)

,” for more 

information.
0 DSPI_PCS5/PCSS is used as the peripheral chip select 5 signal
1 DSPI_PCS5/PCSS is used as an active-low PCS strobe signal

24

ROOE

Receive FIFO overflow overwrite enable. Enables an RX FIFO overflow condition to ignore the incoming serial data 
or to overwrite existing data. If the RX FIFO is full and new data is received, data from the transfer that generated 
the overflow is ignored or shifted in to the shift register. If the ROOE bit is set, incoming data is shifted into the shift 
register. If the ROOE bit is cleared, incoming data is ignored. See 

Section 31.4.6.6, “Receive FIFO Overflow Interrupt 

Request (RFOF)

,” for more information.

0 Incoming data is ignored
1 Incoming data is shifted in to the shift register

23–16

PCSIS

n

Peripheral chip select inactive state. Determines the inactive state of the DSPI_PCS

n

 signal. 

0 The inactive state of DSPI_PCS

n

 is low

1 The inactive state of DSPI_PCS

n

 is high

Note:

DSPI_PCS7, DSPI_PCS6, and DSPI_PCS4 are not implemented on this device. Therefore, these 
corresponding bits are reserved.

Note:

DSPI_PCS0/SS must be configured as inactive high for slave mode operation.

15

Reserved, must be cleared.

14

MDIS

Module disable. Allows the clock to be stopped to non-memory mapped logic in DSPI effectively putting DSPI in a 
software controlled power-saving state. See 

Section 31.4.7, “Power Saving Features,”

 for more information. This bit 

is set at reset.
0 Enable DSPI clocks
1 Allow external logic to disable DSPI clocks

13

DIS_TXF

Disable transmit FIFO. When the TX FIFO is disabled, transmit part of the DSPI operates as a simplified 
double-buffered SPI. See 

Section 31.4.2.3, “FIFO Disable Operation,”

 for details.

0 TX FIFO is enabled
1 TX FIFO is disabled

12

DIS_RXF

Disable receive FIFO. When the RX FIFO is disabled, receive part of the DSPI operates as a simplified 
double-buffered SPI. See 

Section 31.4.2.3, “FIFO Disable Operation

 for details.”

0 RX FIFO is enabled
1 RX FIFO is disabled

11

CLR_TXF

Clear TX FIFO. Flushes the TX FIFO. The CLR_TXF bit is always read as zero.
0 Do not clear the TX FIFO counter
1 Clear the TX FIFO counter

Note:

When the respective FIFO is disabled, this bit does has no effect.

10

CLR_RXF

Clear RX FIFO. Flushes the RX FIFO. The CLR_RXF bit is always read as zero.
0 Do not clear the RX FIFO counter
1 Clear the RX FIFO counter

Note:

When the respective FIFO is disabled, this bit does has no effect.

9–8

SMPL_PT

Sample point. Allows host software to select when the DSPI master samples SIN in modified transfer format. 

Figure 31-17

 shows where the master can sample the SIN pin.

00 0 system clocks between DSPI_SCK edge and DSPI_SIN sample
01 1 system clock between DSPI_SCK edge and DSPI_SIN sample
10 2 system clocks between DSPI_SCK edge and DSPI_SIN sample
11 Reserved

Table 31-3. DSPI_MCR Field Descriptions (continued)

Field

Description

Summary of Contents for MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands