manualshive.com logo in svg

Freescale Semiconductor MCF54455, Reference Manual

Share
Download
Freescale Semiconductor MCF54455 Reference Manual Download Page 771

DMA Serial Peripheral Interface (DSPI)

31-18

Freescale Semiconductor

Address: 0xFC05_C034 (DSPI_PUSHR)

Access: User Read/Write

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

R

CONT

CTAS

EOQ

CT

CNT

0

0

PCS7 PCS6 PCS5 PCS4 PCS3 PCS2 PCS1 PCS0

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

R

TXDATA

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Figure 31-7.  DSPI Push Transmit FIFO Register (DSPI_PUSHR)

Table 31-8. DSPI_PUSHR Field Descriptions

Field

Description

31

CONT

Continuous peripheral chip select enable. Selects a continuous selection format. The bit is used in SPI master mode. 
The bit enables the selected PCS signals to remain asserted between transfers. See 

Section 31.4.4.5, “Continuous 

Selection Format

,” for more information.

0 Return DSPI_PCS

n

 signals to their inactive state between transfers

1 Keep DSPI_PCS

n

 signals asserted between transfers

30–28

CTAS

Clock and transfer attributes select. Selects which of the DSPI_CTAR

n

 registers is used to set the transfer attributes 

for the associated SPI frame. This field is used only in SPI master mode. In SPI slave mode, DSPI_CTAR0 is used 
instead.
000 DSPI_CTAR0
001 DSPI_CTAR1
010 DSPI_CTAR2
011 DSPI_CTAR3
100 DSPI_CTAR4
101 DSPI_CTAR5
110 DSPI_CTAR6
111 DSPI_CTAR7

27

EOQ

End of queue. Provides a means for host software to signal to the DSPI that the current SPI transfer is the last in a 
queue. At the end of the transfer the DSPI_SR[EOQF] bit is set. This bit is used only in SPI master mode.
0 The SPI data is not the last data to transfer
1 The SPI data is the last data to transfer

26

CTCNT

Clear SPI_TCNT. Provides a means for host software to clear the SPI transfer counter. The CTCNT bit clears the 
DSPI_TCR[SPI_TCNT] field. The SPI_TCNT field is cleared before transmission of the current SPI frame begins. 
This bit is used only in SPI master mode.
0 Do not clear DSPI_TCR[SPI_TCNT] field
1 Clear DSPI_TCR[SPI_TCNT] field

25–24

Reserved, must be cleared.

Summary of Contents for MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands