manualshive.com logo in svg

Freescale Semiconductor MCF54455, Reference Manual

Share
Download
Freescale Semiconductor MCF54455 Reference Manual Download Page 297

Chip Configuration Module (CCM)

11-10

Freescale Semiconductor

10–8

BMT

Bus monitor timing field. Selects the timeout period in FlexBus clock cycles for the bus monitor:

Timeout period for external bus cycles equals 2

(16-BMT)

 FB_CLK cycles

000 65536
001 32768
010 16384
011 8192
100 4096
101 2048
110 1024
111 512

7

SSIPUE

SSI RXD/TXD pull enable. Enables the internal weak pull cells on any external pin where either the SSI receive 
data (RXD) function or SSI transmit data (TXD) function is available. The affected pins include SSI_RXD, and 
SSI_TXD.
0 SSI data pin weak pull cells disabled.
1 SSI data pin weak pull cells enabled.

Note:

The SSIPUE bit enables only the pull cells when the SSI RXD and TXD functions are currently selected 
for the affected pins. See the 

Chapter 16, “Pin Multiplexing and Control,”

 for information on how to enable 

the SSI functions on those pins.

6

SSIPUS

SSI RXD/TXD pull select. Selects whether the internal weak pull cells enabled by the SSIPUE bit are pull up or 
pull down.
0 SSI data pins are pulled down.
1 SSI data pins are pulled up.

Note:

The SSIPUS bit has no effect when the SSIPUE bit is cleared.

5

TIMDMA

Timer DMA mux selection. Selects between the timer DMA signals and SSI DMA signals as those signals are 
mapped to DMA channels 9-12. Refer to the 

Chapter 19, “Enhanced Direct Memory Access (eDMA),”

 for more 

details on the DMA controller.
0 SSI RX0, SSI RX1, SSI TX0, and SSI TX1 DMA signals mapped to DMA channels 9 – 12, respectively.
1 Timer 0 – 3 DMA signals mapped to DMA channels 9 – 12, respectively.

4

SSISRC

SSI clock source. Selects between the PLL and the external SSI_CLKIN pin as the source of the SSI baud clock.
0 SSI_CLKIN pin directly drives SSI baud clock.
1 PLL drives SSI baud clock with fractionally divided CPU clock.

3

Reserved, must be cleared.

2

USBPUD

USB transceiver pull-up disable. Disables the USB OTG controller from driving the internal transceiver pull-up.
0 USB OTG drives the internal transceiver pull-up.
1 Internal transceiver pull-up is disabled. The USB_PULLUP signal is used to trigger the external pull-up.

1

USBOC

USB VBUS over-current sense polarity. Selects the polarity of the USB VBUS over-current sense signal driven 
off-chip.
0 USB_VBUS_OC is active high.
1 USB_VBUS_OC is active low.

0

USBSRC

USB clock source. Selects between the PLL and the external USB_CLKIN external pin as the clock source for 
the serial and ULPI interfaces of the USB module.
0 USB_CLKIN pin drives USB serial interface clocks.
1 PLL drives USB serial interface clocks.

Table 11-8. MISCCR Field Descriptions (continued)

Field

Description

Summary of Contents for MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands