manualshive.com logo in svg

Freescale Semiconductor MCF54455, Reference Manual

Share
Download
Freescale Semiconductor MCF54455 Reference Manual Download Page 395

Interrupt Controller Modules

17-6

Freescale Semiconductor

17.2.3

Interrupt Force Registers (INTFRCH

n

, INTFRCL

n

)

The INTFRCH

n

 and INTFRCL

n

 registers are each 32 bits in size and provide a mechanism to allow 

software generation of interrupts for each possible source for functional or debug purposes. The system 
design may reserve one or more sources to allow software to self-schedule interrupts by forcing one or 
more of these bits (set to force request, clear to negate request) in the appropriate INTFRC

n

 register. The 

INTFRCL

n

 register forces interrupts for sources 0 to 31, while the INTFRCH

n

 register forces interrupts 

for sources 32 to 63. The assertion of an interrupt request via the interrupt force register is not affected by 
the interrupt mask register. The INTFRC

n

 registers are cleared by reset.

Table 17-5. IMRH

n

 Field Descriptions

Field

Description

31–0

INT_MASK

Interrupt mask. Each bit corresponds to an interrupt source. The corresponding IMRH

n

 bit determines whether an 

interrupt condition can generate an interrupt. The corresponding IPRH

n

 bit reflects the state of the interrupt signal 

even if the corresponding IMRH

n

 bit is set.

0 The corresponding interrupt source is not masked
1 The corresponding interrupt source is masked

Address 0xFC04_800C (IMRL0)

0xFC04_C00C (IMRL1)

Access: User read/write

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

R

INT_MASK

W

Reset 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Figure 17-4. Interrupt Mask Register Low (IMRL

n

)

Table 17-6. IMRL

n

 Field Descriptions

Field

Description

31–0

INT_MASK

Interrupt mask. Each bit corresponds to an interrupt source. The corresponding IMRL

n

 bit determines whether an 

interrupt condition can generate an interrupt. The corresponding IPRL

n

 bit reflects the state of the interrupt signal 

even if the corresponding IMRL

n

 bit is set.

0 The corresponding interrupt source is not masked
1 The corresponding interrupt source is masked

Address 0xFC04_8010 (INTFRCH0)

0xFC04_C010 (INTFRCH1)

Access: User read/write

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

R

INTFRCH

W

Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Figure 17-5. Interrupt Force Register High (INTFRCH

n

)

Summary of Contents for MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands