manualshive.com logo in svg

Freescale Semiconductor MCF54455, Reference Manual

Share
Download
Freescale Semiconductor MCF54455 Reference Manual Download Page 87

ColdFire Core

3-21

Freescale Semiconductor

 

If the processor is not in trace mode and executes a stop instruction where the immediate operand sets 
SR[T], hardware loads the SR and generates a trace exception. The PC in the exception stack frame points 
to the instruction after the stop, and the SR reflects the value loaded in step 2. 

Because ColdFire processors do not support any hardware stacking of multiple exceptions, it is the 
responsibility of the operating system to check for trace mode after processing other exception types. As 
an example, consider a TRAP instruction execution while in trace mode. The processor initiates the trap 
exception and then passes control to the corresponding handler. If the system requires that a trace exception 
be processed, it is the responsibility of the trap exception handler to check for this condition (SR[T] in the 
exception stack frame set) and pass control to the trace handler before returning from the original 
exception.

3.3.4.7

Unimplemented Line-A Opcode

A line-A opcode is defined when bits 15-12 of the opword are 0b1010. This exception is generated by the 
attempted execution of an undefined line-A opcode.

3.3.4.8

Unimplemented Line-F Opcode

A line-F opcode is defined when bits 15-12 of the opword are 0b1111. This exception is generated when 
attempting to execute an undefined line-F opcode.

3.3.4.9

Debug Interrupts

See 

Chapter 34, “Debug Module

,

” 

for a detailed explanation of these exceptions, which are generated in 

response to hardware breakpoint register triggers. The processor does not generate an IACK cycle, but 
rather calculates the vector number internally (vector number 12 or 13, depending on the type of 
breakpoint trigger). Additionally, SR[M,I] are unaffected by the interrupt.

Separate exception vectors are provided for PC breakpoints and for address/data breakpoints. In the case 
of a two-level trigger, the last breakpoint determines the vector. There are two unique vectors for these 
exceptions: vector 0x030 corresponds to non-PC breakpoints and vector 0x034 corresponds to PC 
breakpoints.

3.3.4.10

RTE and Format Error Exception

When an RTE instruction is executed, the processor first examines the 4-bit format field to validate the 
frame type. For a ColdFire core, any attempted RTE execution (where the format is not equal to {4,5,6,7}) 
generates a format error. The exception stack frame for the format error is created without disturbing the 
original RTE frame and the stacked PC pointing to the RTE instruction.

The selection of the format value provides some limited debug support for porting code from M68000 
applications. On M68000 family processors, the SR was located at the top of the stack. On those 
processors, bit 30 of the longword addressed by the system stack pointer is typically zero. Thus, if an RTE 
is attempted using this old format, it generates a format error on a ColdFire processor.

If the format field defines a valid type, the processor: (1) reloads the SR operand, (2) fetches the second 
longword operand, (3) adjusts the stack pointer by adding the format value to the auto-incremented address 

Summary of Contents for MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands