manualshive.com logo in svg

Freescale Semiconductor MCF54455, Reference Manual

Share
Download
Freescale Semiconductor MCF54455 Reference Manual Download Page 231

Universal Serial Bus Interface – On-The-Go Module

10-24

Freescale Semiconductor

Table 10-21. USBINTR Field Descriptions

Field

Description

31–26

Reserved, must be cleared.

25

TIE1

General purpose timer 1 interrupt enable. When this bit and USBSTS[GPTINT1] are set, the USB controller 
issues an interrupt to the processor. The interrupt is acknowledged by clearing GPTINT1.
0 Disabled
1 Enabled

24

TIE0

General purpose timer 0 interrupt enable. When this bit and USBSTS[GPTINT0] are set, the USB controller 
issues an interrupt to the processor. The interrupt is acknowledged by clearing GPTINT0.
0 Disabled
1 Enabled

23–20

Reserved, must be cleared.

19

UPIE

USB host periodic interrupt enable. When this bit and USBSTS[USBHSTPERINT] are set, the host controller 
issues an interrupt at the next interrupt threshold. The interrupt is acknowledged by clearing USBHSTPERINT.

18

UAIE

USB host asynchronous interrupt enable. When this bit and USBSTS[USBHSTASYNCINT] are set, the host 
controller issues an interrupt at the next interrupt threshold. The interrupt is acknowledged by clearing 
USBHSTASYNCINT.

17

Reserved, must be cleared.

16

NAKE

NAK interrupt enable. When this bit and the USBSTS[NAKI] bit are set, an interrupt generates.
0 Disabled
1 Enabled

15–11

Reserved, must be cleared.

10

ULPIE

ULPI enable. When this bit and USBSTS[ULPII] are set, controller issues an interrupt. The interrupt is 
acknowledged by writing a 1 to USBSTS[ULPII].

9

Reserved, must be cleared.

8

SLE

Sleep (DC suspend) enable. A non-EHCI bit. When this bit is set and the USBSTS[] bit transitions, USB OTG 
controller issues an interrupt. Software writing a 1 to the USBSTS[] bit acknowledges the interrupt. Used only 
in device mode.
0 Disabled
1 Enabled

7

SRE

SOF-received enable. This is a non-EHCI bit. When this bit and the USBSTS[SRI] bit are set, controller issues 
an interrupt. Software clearing the USBSTS[SRI] bit acknowledges the interrupt.
0 Disabled
1 Enabled

6

URE

USB-reset enable. A non-EHCI bit. When this bit and the USBSTS[URI] bit are set, device controller issues an 
interrupt. Software clearing the USBSTS[URI] bit acknowledges the interrupt. Used only in device mode.
0 Disabled
1 Enabled

5

AAE

Interrupt on async advance enable. When this bit and the USBSTS[AAI] bit are set, controller issues an 
interrupt at the next interrupt threshold. Software clearing the USBSTS[AAI] bit acknowledges the interrupt. 
Used only in host mode.
0 Disabled
1 Enabled

Summary of Contents for MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands