manualshive.com logo in svg

Freescale Semiconductor MCF54455, Reference Manual

Share
Download
Freescale Semiconductor MCF54455 Reference Manual Download Page 791

DMA Serial Peripheral Interface (DSPI)

31-38

Freescale Semiconductor

31.5

Initialization/Application Information

31.5.1

How to Change Queues

DSPI queues are not part of the DSPI module, but the DSPI includes features in support of queue 
management. This section presents an example of how to change queues for the DSPI.

1. The last command word from a queue is executed. The EOQ bit in the command word is set to 

indicate to the DSPI that this is the last entry in the queue.

2. At the end of the transfer, corresponding to the command word with EOQ set is sampled, the EOQ 

flag, DSPI_SR[EOQF] is set.

3. The setting of the EOQF flag disables serial transmission and serial reception of data, putting the 

DSPI in the stopped state. The TXRXS bit is cleared to indicate the stopped state.

4. The eDMA continues to fill TX FIFO until it is full or step 5 occurs.
5. Disable DSPI DMA transfers by disabling the DMA enable request for the DMA channel assigned 

to TX FIFO and RX FIFO. This is done by clearing the corresponding DMA enable request bits in 
the eDMA controller.

6. Ensure all received data in RX FIFO has been transferred to memory receive queue by reading the 

DSPI_SR[RXCNT] bit or by checking the DSPI_SR[RFDF] bit after each read operation of the 
DSPI_POPR register.

7. Modify DMA descriptor of TX and RX channels for new queues.
8. Flush TX FIFO by writing a 1 to the DSPI_MCR[CLR_TXF] bit; Flush RX FIFO by writing a 1 

to the DSPI_MCR[CLR_RXF] bit.

9. Clear transfer count by setting the CTCNT bit in the command word of the first entry in the new 

queue or via CPU writing directly to the DSPI_TCR[SPI_TCNT] field.

10. Enable DMA channel by enabling the DMA enable request for the DMA channel assigned to the 

DSPI TX FIFO, and RX FIFO by setting the corresponding DMA set enable request bit.

11. Enable serial transmission and serial reception of data by clearing the EOQF bit.

31.5.2

Switching Master and Slave Mode

When changing modes in the DSPI, follow the steps below to guarantee proper operation.

1. Halt the DSPI by setting DSPI_MCR[HALT].
2. Clear the transmit and receive FIFOs by writing a 1 to the CLR_TXF and CLR_RXF bits in 

DSPI_MCR.

3. Set the appropriate mode in DSPI_MCR[MSTR] and enable the DSPI by clearing 

DSPI_MCR[HALT].

31.5.3

Baud Rate Settings

Table 31-21

 shows the baud rate generated based on the combination of the baud rate prescaler PBR and 

the baud rate scaler BR in the DSPI_CTAR

n

 registers. The values calculated assume a 100 MHz system 

frequency.

Summary of Contents for MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands