manualshive.com logo in svg

Freescale Semiconductor MCF54455, Reference Manual

Share
Download
Freescale Semiconductor MCF54455 Reference Manual Download Page 663

Fast Ethernet Controllers (FEC0 and FEC1)

26-45

Freescale Semiconductor

26.5.11 Full Duplex Flow Control

Full-duplex flow control allows you to transmit pause frames and to detect received pause frames. Upon 
detection of a pause frame, MAC data frame transmission stops for a given pause duration.

To enable PAUSE frame detection, the FEC must operate in full-duplex mode (TCR

n

[FDEN] set) with 

flow control (RCR

n

[FCE] set). The FEC detects a pause frame when the fields of the incoming frame 

match the pause frame specifications, as shown in 

Table 26-39

. In addition, the receive status associated 

with the frame should indicate that the frame is valid.

The receiver and microcontroller modules perform PAUSE frame detection. The microcontroller runs an 
address recognition subroutine to detect the specified pause frame destination address, while the receiver 
detects the type and opcode pause frame fields. On detection of a pause frame, TCR

n

[GTS] is set by the 

FEC internally. When transmission has paused, the EIR

n

[GRA] interrupt is asserted and the pause timer 

begins to increment. The pause timer uses the transmit backoff timer hardware for tracking the appropriate 
collision backoff time in half-duplex mode. The pause timer increments once every slot time, until 
OPD

n

[PAUSE_DUR] slot times have expired. On OPD

n

[PAUSE_DUR] expiration, TCR

n

[GTS] is 

cleared allowing MAC data frame transmission to resume. The receive flow control pause status bit 
(TCR

n

[RFC_PAUSE]) is set while the transmitter pauses due to reception of a pause frame.

To transmit a pause frame, the FEC must operate in full-duplex mode and you must set flow control pause 
(TCR

n

[TFC_PAUSE]). After TCR

n

[TFC_PAUSE] is set, the transmitter sets TCR

n

[GTS] internally. 

When the transmission of data frames stops, the EIR

n

[GRA] (graceful stop complete) interrupt asserts and 

the pause frame is transmitted. TCR

n

[TFC_PAUSE,GTS] are then cleared internally. 

You must specify the desired pause duration in the OPD

n

 register.

FDFF_FFFF_FFFF

0x3C

60

DDFF_FFFF_FFFF

0x3D

61

9DFF_FFFF_FFFF

0x3E

62

BDFF_FFFF_FFFF

0x3F

63

Table 26-39. PAUSE Frame Field Specification

48-bit Destination Address

0x0180_C200_0001 or Physical Address

48-bit Source Address

Any

16-bit Type

0x8808

16-bit Opcode

0x0001

16-bit PAUSE Duration

0x0000 – 0xFFFF

Table 26-38. Destination Address to 6-Bit Hash (continued)

48-bit DA

6-bit Hash

(in hex)

Hash Decimal 

Value

Summary of Contents for MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands