manualshive.com logo in svg

Freescale Semiconductor MCF54455, Reference Manual

Share
Download
Freescale Semiconductor MCF54455 Reference Manual Download Page 641

Fast Ethernet Controllers (FEC0 and FEC1)

26-23

Freescale Semiconductor

26.4.14 Opcode/Pause Duration Registers (OPD0 & OPD1)

The OPD

n

 is read/write accessible. This register contains the 16-bit opcode and 16-bit pause duration 

fields used in transmission of a PAUSE frame. The opcode field is a constant value, 0x0001. When another 
node detects a PAUSE frame, that node pauses transmission for the duration specified in the pause duration 
field. The lower 16 bits of this register are not reset and you must initialize them.

26.4.15 Descriptor Individual Upper Address Registers (IAUR0 & IAUR1)

IAUR

n

 contains the upper 32 bits of the 64-bit individual address hash table. The address recognition 

process uses this table to check for a possible match with the destination address (DA) field of receive 
frames with an individual DA. This register is not reset and you must initialize it.

Address: 0xFC03_00E8 (PAUR0)

0xFC03_40E8 (PAUR1)

Access: User read/write

 

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

R

PADDR2

TYPE

W

Reset — — — — — — — — — — — — — — — — 1 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0

Figure 26-13. Physical Address Upper Register (PAUR

n

)

Table 26-17. PAUR

n

 Field Descriptions

Field

Description

31–16

PADDR2

Bytes 4 (bits 31:24) and 5 (bits 23:16) of the 6-byte individual address used for exact match, and the source address 
field in PAUSE frames.

15–0

TYPE

Type field in PAUSE frames. These 16 read-only bits are a constant value of 0x8808.

Address: 0xFC03_00EC (OPD0)

0xFC03_40EC (OPD1)

Access: User read/write

 

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

R

OPCODE

PAUSE_DUR

W

Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 — — — — — — — — — — — — — — — —

Figure 26-14. Opcode/Pause Duration Register (OPD

n

)

Table 26-18. OPD

n

 Field Descriptions

Field

Description

31–16

OPCODE

Opcode field used in PAUSE frames. These read-only bits are a constant, 0x0001.

15–0

PAUSE_DUR

Pause Duration field used in PAUSE frames.

Summary of Contents for MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands