manualshive.com logo in svg

Freescale Semiconductor MCF54455, Reference Manual

Share
Download
Freescale Semiconductor MCF54455 Reference Manual Download Page 115

Memory Management Unit (MMU)

4-14

Freescale Semiconductor

4.3.1.2.9

Changes to ACRs and CACR

New ACR and CACR bits improve address granularity and supervisor mode protection and memory 
functionality for physical- and virtual- address environments.

4.3.1.2.10

ACR Address Improvements

The ACR registers provide a 16-Mbyte address window. For a given request address, if the ACR is valid 
and the request mode matches the mode specified in the supervisor mode field (ACR

n

[S]), hit 

determination is specified as:

ACRx_Hit = 0;
if ((address[31:24] and  ~ACR

n

[23:16]) == (ACR

n

[31:24] and  ~ACR

n

[23:16]))

ACRx_Hit = 1;

With this hit function, ACRs can assign address attributes for user or supervisor requests to memory spaces 
of at least 16 Mbytes (through the address mask). With the MMU definition, the ACR hit function is 
improved by the address mask mode bit (ACR

n

[AMM]), which supports finer address granularity. See 

Table 4-10

.

The revised hit determination becomes:

ACRx_Hit = 0;
if (ACR

n

[10] == 1)

if ((address[31–24] == ACR

n

[31–24])) &&

((address[23–20] and  ~ACR

n

[19–16]) == (ACR

n

[23–20] and  ~ACR

n

[19–16])))

ACRx_Hit = 1;

else if (address[31–24] and  ~ACR

n

[23–16]) == (ACR

n

[31–24] and  ~ACR

n

[23–16]))

ACRx_Hit = 1;

Table 4-10. New ACR and CACR Bits

Field

Description

ACR

n

[10]

AMM

Address mask mode. Determines access to the associated address space.
0 The ACR hit function is the same as previous versions, allowing control of a 16-Mbyte or greater memory 

region.

1 The upper 8 bits of the address and ACR are compared without a mask function; bits 23–20 of the address 

and ACR are compared masked by ACR[19–16], allowing control of a 1- to 16-Mbyte region.

Reset value is 0.

ACR

n

[3]

SP

Supervisor protect. Determines access to the associated address space.
0 Supervisor and user access allowed.
1 Only supervisor access allowed. Attempted user access causes an access error exception.
Reset value is 0.

CACR[23]

DDSP

Default data supervisor protect. Determines access to the associated data space.
0 Supervisor and user access allowed.
1 Only supervisor access allowed. Attempted user access causes an access error exception.
Reset value is 0.

CACR[7]

DISP

Default instruction supervisor protect. Determines access to the associated instruction space. 
0 Supervisor and user access allowed.
1 Only supervisor access allowed. Attempted user access causes access error exception
Reset value is 0.

Summary of Contents for MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands