manualshive.com logo in svg

Freescale Semiconductor MCF54455, Reference Manual

Share
Download
Freescale Semiconductor MCF54455 Reference Manual Download Page 666

Fast Ethernet Controllers (FEC0 and FEC1)

Freescale Semiconductor

26-48

26.5.17.1.2

Retransmission Attempts Limit Expired

When this error occurs, the FEC terminates transmission. All remaining buffers for that frame are flushed 
and closed, and EIR

n

[RL] is set. The FEC then continues to the next transmit buffer descriptor and begins 

transmitting the next frame. The RL interrupt is asserted if enabled in the EIMR

n

 register.

26.5.17.1.3

Late Collision

When a collision occurs after the slot time (512 bits starting at the Preamble), the FEC terminates 
transmission. All remaining buffers for that frame are flushed and closed, and EIR

n

[LC] is set. The FEC 

then continues to the next transmit buffer descriptor and begin transmitting the next frame. The LC 
interrupt is asserted if enabled in the EIMR

n

 register.

26.5.17.1.4

Heartbeat

Some transceivers have a self-test  called heartbeat or signal quality error. To signify a good self-test, the 
transceiver indicates a collision to the FEC within four microseconds after completion of a frame 
transmitted by the Ethernet controller. This indication of a collision does not imply a real collision error 
on the network, but is rather an indication that the transceiver continues to function properly. This is the 
heartbeat condition.

If TCR

n

[HBC] is set and the heartbeat condition is not detected by the FEC after a frame transmission, a 

heartbeat error occurs. When this error occurs, the FEC closes the buffer, sets EIR

n

[HB], and generates 

the HBERR interrupt if it is enabled.

26.5.17.2 Reception Errors

26.5.17.2.1

Overrun Error

If the receive block has data to put into the receive FIFO and the receive FIFO is full, FEC sets 
RxBD

n

[OV]. All subsequent data in the frame is discarded and subsequent frames may also be discarded 

until the receive FIFO is serviced by the DMA and space is made available. At this point the receive 
frame/status word is written into the FIFO with the OV bit set. The driver must discard this frame.

26.5.17.2.2

Non-Octet Error (Dribbling Bits)

The Ethernet controller manages up to seven dribbling bits when the receive frame terminates past an 
non-octet aligned boundary. Dribbling bits are not used in the CRC calculation. If there is a CRC error, the 
frame non-octet aligned (NO) error is reported in the RxBD

n

. If there is no CRC error, no error is reported.

26.5.17.2.3

CRC Error

When a CRC error occurs with no dribble bits, FEC closes the buffer and sets RxBD

n

[CR]. CRC checking 

cannot be disabled, but the CRC error can be ignored if checking is not required.

26.5.17.2.4

Frame Length Violation

When the receive frame length exceeds MAX_FL bytes the BABR interrupt is generated, and RxBD

n

[LG] 

is set. The frame is not truncated unless the frame length exceeds 2047 bytes.

Summary of Contents for MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands