manualshive.com logo in svg

Freescale Semiconductor MCF54455, Reference Manual

Share
Download
Freescale Semiconductor MCF54455 Reference Manual Download Page 852

Debug Module

Freescale Semiconductor

34-10

23–20

HRL

Hardware revision level. Indicates, from the BDM port only, the level of debug module functionality. An emulator 
could use this information to identify the level of functionality supported.
0000 Revision A
0001 Revision B
0010 Revision C
0011 Revision D
1001 Revision B+
1011 Revision D+ (This is the value used for this device)
1111 Revision D+PSTB

19

Reserved, must be cleared. 

18

BKD

Breakpoint disable. Disables the normal BKPT input signal functionality, and allows the assertion of this pin to 
generate a debug interrupt.
0 Normal operation
1 BKPT is edge-sensitive: a high-to-low edge on BKPT signals a debug interrupt to the ColdFire core. The 

processor makes this interrupt request pending until the next sample point occurs, when the exception is 
initiated. In the ColdFire architecture, the interrupt sample point occurs once per instruction. There is no 
support for nesting debug interrupts.

17

PCD

PSTCLK disable.
0 PSTCLK is fully operational
1 Disables the generation of the PSTCLK and PSTDDATA output signals, and forces these signals to remain 

quiescent

16

IPW

Inhibit processor writes. Setting IPW inhibits processor-initiated writes to the debug module’s programming model 
registers. Only commands from the external development system can modify IPW.

15

MAP

Force processor references in emulator mode.
0 All emulator-mode references are mapped into supervisor code and data spaces.
1 The processor maps all references while in emulator mode to a special address space, TT equals 10, 

TM equals 101 or 110. The internal SRAM and caches are disabled. 

14

TRC

Force emulation mode on trace exception.
0 The processor enters supervisor mode
1 The processor enters emulator mode when a trace exception occurs

13

EMU

Force emulation mode.
0 Do not force emulator mode
1 The processor begins executing in emulator mode. See 

Section 34.4.2.2, “Emulator Mode”

.

12–11

DDC

Debug data control. Controls operand data capture for PSTDDATA, which displays the number of bytes defined 
by the operand reference size before the actual data; byte displays 8 bits, word displays 16 bits, and long displays 
32 bits (one nibble at a time across multiple PSTCLK clock cycles). See 

Table 34-30

.

00 No operand data is displayed.
01 Capture all write data.
10 Capture all read data.
11 Capture all read and write data.

10

UHE

User halt enable. Selects the CPU privilege level required to execute the HALT instruction.
0 HALT is a supervisor-only instruction.
1 HALT is a supervisor/user instruction.

Table 34-7. CSR Field Descriptions (continued)

Field

Description

Summary of Contents for MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands