manualshive.com logo in svg

Freescale Semiconductor MCF54455, Reference Manual

Share
Download
Freescale Semiconductor MCF54455 Reference Manual Download Page 877

Debug Module

34-35

Freescale Semiconductor

Command Sequence:

Figure 34-24. 

WAREG

/

WDREG

 Command Sequence

Operand Data:

Longword data is written into the specified address or data register. The data is 
supplied most-significant word first.

Result Data:

Command complete status is indicated by returning 0xFFFF (with S cleared) 
when the register write is complete.

34.4.1.5.3

Read Memory Location (

READ

)

Read data at the longword address. Address space is defined by BAAR[TT,TM]. Hardware forces 
low-order address bits to 0s for word and longword accesses to ensure that word addresses are 
word-aligned and longword addresses are longword-aligned.

Command/Result Formats:

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

Byte

 

Command

0x1

0x9

0x0

0x0

A[31:16]

A[15:0]

 Result

X

X

X

X

X

X

X

X

D[7:0]

Word

Command

0x1

0x9

0x4

0x0

A[31:16]

A[15:0]

Result

D[15:0]

Longword Command

0x1

0x9

0x8

0x0

A[31:16]

A[15:0]

Result

D[31:16]

D[15:0]

Figure 34-25. 

READ

 Command/Result Formats

WAREG/WDREG

???

LS DATA

’NOT READY’

NEXT CMD

’NOT READY’

XXX

BERR

MS DATA

’NOT READY’

NEXT CMD

’CMD COMPLETE’

Summary of Contents for MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands