manualshive.com logo in svg

Freescale Semiconductor MCF54455, Reference Manual

Share
Download
Freescale Semiconductor MCF54455 Reference Manual Download Page 598

Advanced Technology Attachment (ATA)

Freescale Semiconductor

23-23

23.4.6

Using DMA Mode to Transmit Data to ATA Bus

Apart from PIO mode, the ATA interface supports also multiword DMA (MDMA) and ultra DMA 
(UDMA) mode to transfer data. DMA mode can transmit data to the drive (DMA out transfer). In DMA 
transmit mode, the protocol engine transfers data from the FIFO to the drive using multiword DMA or ultra 
DMA protocol. The transfer pauses when:

•

The FIFO is empty.

•

The drive deasserts its DMA request signal, ATA_DMARQ.

•

The ATA_CR[DMAPEND] bit is cleared.

When the cause of transfer pausing is removed, the transfer restarts. The end of transfer is signalled by the 
drive to the host by asserting the ATA_INTRQ signal. Alternatively, the host can read the device status 
register. In this register, the drive also indicate if the transfer has ended.

The host system DMA manages the transfer of data from the memory to the FIFO. When the FIFO filling 
is below the alarm threshold, the DMA must read one packet of data from the main memory and store this 
in the FIFO. In doing so, the DMA prevents the FIFO from becoming empty and keeps the transfer from 
FIFO to drive running.

The steps for setting up a DMA data transfer from device to host are:

1. Make sure the ATA bus is not in reset and all timing registers are programmed.
2. Make sure the FIFO is empty by reading it until empty or by resetting it.
3. Initialize the DMA channel associated with ATA transmit. Every time ATA transmit DMA request 

asserts, the DMA should read <packetsize> longwords from the main memory, and write them to 
the FIFO. (typical packetsize is 8 longwords). Program the DMA so it does not transfer more than 
<sectorsize> longwords in total.

4. Write FIFO_SIZE - 2 * <packetsize> to the FIFO_ALARM register. In this way, the FIFO requests 

attention to DMA when there is room for at least one extra packet. FIFO_SIZE should be given in 
halfwords. (typical 64 halfwords)

5. To make the ATA ready for a DMA transfer from host to device, perform the following steps:

a) Make sure the FIFO is enabled by setting the ATA_CR[FEN] bit.
b) Set the ATA_CR[FREFILL] bit, which enables the DMA to fill FIFO.
c) Program ATA_CR[DMAPEND] equals 1 and ATA_CR[DMADIR] equals 1. Also, select the 

DMA mode; ATA_CR[DMAMODE] equals 0 for multiword DMA or ATA_CR[DMAMODE] 
equals 1 for ultra DMA.

6. The host side of the DMA is now ready. Send commands to the drive in PIO mode that cause it to 

request DMA transfer on the ATA bus. The nature of these commands is beyond the scope of this 
document. Consult the ATA specification for more information on how to communicate with the 
drive.

7. When the drive now requests DMA transfer by asserting ATA_DMARQ, the ATA interface 

acknowledges with ATA_DMACK, and the transfer starts. Data is transferred automatically from 
the FIFO, and also from host memory to FIFO.

Summary of Contents for MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands