manualshive.com logo in svg

Freescale Semiconductor MCF54455, Reference Manual

Share
Download
Freescale Semiconductor MCF54455 Reference Manual Download Page 267

Universal Serial Bus Interface – On-The-Go Module

10-60

Freescale Semiconductor

10.5.3.3

Managing Endpoints

The USB 2.0 specification defines an endpoint (also called a device endpoint or an address endpoint) as a 
uniquely addressable portion of a USB device that can source or sink data in a communications channel 
between the host and the device. Combination of the endpoint number and the endpoint direction specifies 
endpoint address.

The channel between the host and an endpoint at a specific device represents a data pipe. Endpoint 0 for a 
device is always a control type data channel used for device discovery and enumeration. Other types of 
endpoints are supported by USB include bulk, interrupt, and isochronous. Each endpoint type has specific 
behavior related to packet response and error managing. Find more detail on endpoint operation in the USB 
2.0 specification.

The USB OTG supports up to four endpoint specified numbers. The DCD can enable, disable, and 
configure each endpoint.

Each endpoint direction is essentially independent and can have differing behavior in each direction. For 
example, the DCD can configure endpoint 1-IN to be a bulk endpoint and endpoint 1-OUT to be an 
isochronous endpoint. This helps to conserve the total number of endpoints required for device operation. 
The only exception is that control endpoints must use both directions on a single endpoint number to 
function as a control endpoint. Endpoint 0, for example, is always a control endpoint and uses both 
directions.

Each endpoint direction requires a queue head allocated in memory. If the maximum is four endpoint 
numbers (one for each endpoint direction used by the device controller), eight queue heads are required. 
The operation of an endpoint and use of queue heads are described later in this document.

10.5.3.3.1

Endpoint Initialization

After hardware reset, all endpoints except endpoint 0 are uninitialized and disabled. The DCD must 
configure and enable each endpoint by writing to the appropriate EPCR

n

 register. Each EPCR

n

 is split into 

an upper and lower half. The lower half of EPCR

n

 configures the receive or OUT endpoint, and the upper 

half configures the corresponding transmit or IN endpoint. Control endpoints must be configured the same 
in the upper and lower half of the EPCR

n

 register; otherwise, behavior is undefined. 

Table 10-51

 shows 

how to construct a configuration word for endpoint initialization.

Table 10-51. Device Controller Endpoint Initialization

Field

Value

Data Toggle Reset (TXR, RXR)

1 Synchronize the data PIDs

Data Toggle Inhibit (TXI, RXI)

0 PID sequencing disabled

Endpoint Type (TXT, RXT)

00 Control
01 Isochronous
10 Bulk
11 Interrupt

Endpoint Stall (TXS, RXS)

0 Not stalled

Summary of Contents for MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands