manualshive.com logo in svg

Freescale Semiconductor MCF54455, Reference Manual

Share
Download
Freescale Semiconductor MCF54455 Reference Manual Download Page 282

Universal Serial Bus Interface – On-The-Go Module

Freescale Semiconductor

10-75

10.5.4.1.2

Error Interrupts

Error interrupts are least frequent and should be placed last in the interrupt service routine.

10.5.5

Deviations from the EHCI Specifications

The host mode operation of the USB OTG module is nearly EHCI-compatible with a few minor 
differences. For the most part, the modules conform to the data structures and operations described in 
Section 3, “Data Structures,” and Section 4, “Operational Model,” in the EHCI specification. The 
particulars of the deviations occur in the following areas:

•

Embedded transaction translator—Allows direct attachment of FS and LS devices in host mode 
without the need for a companion controller.

•

Device operation—In host mode, the device operational registers are generally disabled; therefore, 
device mode is mostly transparent when in host mode. However, there are a couple exceptions 
documented in the following sections.

•

Embedded design interface—The module does not have a PCI Interface and therefore the PCI 
configuration registers described in the EHCI specification are not applicable.

For the purposes of the USB OTG implementing a dual-role host/device controller with support for OTG 
applications, it is necessary to deviate from the EHCI specification. Device and OTG operation are not 
specified in the EHCI specification, and thus the implementation supported in the USB OTG module is 
proprietary. 

10.5.5.1

Embedded Transaction Translator Function

The USB host mode supports directly connected full- and low-speed devices without requiring a 
companion controller by including the capabilities of a USB 2.0 high-speed hub transaction translator. 
Although there is no separate transaction translator block in the system, the transaction translator function 
normally associated with a high-speed hub is implemented within the DMA and protocol engine blocks. 
The embedded transaction translator function is an extension to EHCI interface, but makes use of the 
standard data structures and operational models existing in the EHCI specification to support full- and 
low-speed devices.

10.5.5.1.1

Capability Registers

These additions to the capability registers support the embedded Transaction translator function:

•

N_TT added to HSCPARAMS - Host Controller Structural Parameters

•

N_PTT added to HSCPARAMS - Host Controller Structural Parameters

Table 10-62. Error Interrupt Events

Interrupt

Action

USB Error Interrupt.

This error is redundant because it combines USB interrupt and an error status in the dTD. 
The DCD more aptly manages packet-level errors by checking the dTD status field upon 
receipt of USB interrupt (w/ EPCOMPLETE).

System Error

Unrecoverable error. Immediate reset of module; free transfers buffers in progress and 
restart the DCD.

Summary of Contents for MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands