![background image](http://html1.mh-extra.com/html/ducati/749dark/749dark_manual_2537616270.webp)
A
B
C
D
E
F
G
H
L
M
N
P
Mototelaio
Frame
sezione / section
H 2
10
749/749 DARK/749S Aggiornamento/Update
- M.Y. 2006 - edizione/edition 00
Installare il gruppo appena assemblato
sul telaio. Inserire sull'anello esterno
superiore (
D
), la corona di sfere (B)
opportunamente ingrassata.
Montare sul perno di sterzo la pista
interna (C) del cuscinetto, con la parte di
diametro maggiore, rivolta verso l'alto.
Montare l'anello di tenuta (2) con la
superficie piana verso l'alto.
Avvitare manualmente la ghiera di
registro (10) fino a portarla in battuta
sull'anello di tenuta.
Posizionare sulla ghiera la bussola
speciale cod.
88713.1058
sulla quale
applicare la chiave dinamometrica.
Serrare la ghiera di registro (10) alla
coppia prescritta (Sez. C 3).
749S
Per mantenere l’inclinazione del
cannotto originale, far corrispondere
la cava sul cannotto (4) con il foro
passante sul telaio, sede della vite (9)
precedentemente rimossa.
Per modificare l’angolo di sterzo
originale, con una chiave a settore
ruotare di
180°
l'estremità del
canotto (4).
Note
Quando si cambia l’angolo di
sterzo è necessario cambiare la
posizione dell’ammortizzatore di
sterzo e del martelletto bloccasterzo
(Sez. H 3).
Verificare che il foro sul cannotto
eccentrico sia coassiale con il foro
passante sul telaio. A tal fine è
stampigliata nella zona superiore
dell'eccentrico una freccia che
indica la fase.
Riavvitare la vite (9) fino a battuta.
Serrare le viti (7) alla coppia di
serraggio prescritta (Sez. C 3).
Montare nelle apposite sedi i seger (
8
).
Installare la testa di sterzo (11) sulla
ghiera (10) facendo corrispondere le
sedi degli steli forcella con le
corrispondenti sulla base di sterzo.
Rimontare gli steli forcella (Sez. G 3).
Posizionare il martelletto bloccasterzo
e bloccare la vite (5) sulla testa di
sterzo alla coppia prescritta (Sez. C 3).
Se è stata rimossa dalla testa di
sterzo, è necessario lubrificarla con
grasso prescritto.
Operazioni
Rif Sez.
Rimontare
l'ammortizzatore di
sterzo 749/749S
H 3
Rimontare il cupolino
E 2
Rimontare le
carenature laterali
E 1
Install the assembly on the frame.
Grease the ball race (B) and fit it to
the top outer ring (
D
).
Fit the inner ring (C) of the bearing to
the stem, with the larger diameter
side facing upwards.
Install the seal (2) with the flat side
facing upwards.
Grease the ring nut adjuster (10)
and tighten it down by hand until it
locates against the oil seal.
Install on the ring nut the special bush
part no.
88713.1058
, to which the
torque wrench is to be applied.
Tighten the ring nut (10) to the
specified torque (Sect. C 3).
(749S)
To maintain the original steering
head angle, align the recess (4) in
the steering tube with the hole in
the frame for the previously
removed screw (9).
To alter the steering angle, use a
pin wrench to turn the end of the
steering tube (4) through
180°
.
Notes
Whenever the steering angle is
changed, it is also necessary to change
the position of the steering damper
and the steering lock (Sect. H 3).
Check that the hole on the eccentric
head tube is aligned with the hole
through the frame. For this purpose,
there is an arrow stamped on the top
of the eccentric to indicate the angle.
Fully screw in the screw (9).
Tighten the screws (7) to the
specified torque (Sect. C 3).
Fit the circlips (
8
) in their grooves.
Fit the top yoke (11) on the ring
nut (10), aligning the fork leg bores
with the corresponding bores on
the bottom yoke.
Refit the fork legs (Sect. G 3).
Position the steering lock peg and
tighten the steering head screw (5)
to the specified torque (Sect. C 3).
If this screw has been removed from
the steering head, lubricate it first
with the recommended grease.
Operation
See Sect.
Remove the steering
damper 749/749S
H 3
Refit the headlight
fairing
E 2
Refit the side fairings
E 1
88713.1058
10
4
2
C
B
B
11
10
5
9
7
B
Summary of Contents for 749DARK
