![background image](http://html1.mh-extra.com/html/ducati/749dark/749dark_manual_2537616356.webp)
A
B
C
D
E
F
G
H
L
M
N
P
Impianto iniezione - accensione
Ignition - injection system
sezione / section
M 4
32
749/749 DARK/749S Aggiornamento/Update
- M.Y. 2006 - edizione/edition 00
Funzione “Lap Time Memory”
La visualizzazione dei tempi sul giro
registrati è possibile quando la
motocicletta è ferma e il motore è
spento. Per entrare nella funzione
“Lap Time Memory” si deve tenere
premuto il tasto Dx mentre si porta la
chiave in posizione “ON”. Una volta
entrati nella modalità di
visualizzazione rilasciare il tasto: i dati
memorizzati si possono scorrere
premendo il tasto Sx.
Sul display LCD viene visualizzato il
numero associato al giro, il tempo
impiegato e la velocità massima
raggiunta durante il giro. Il contagiri
visualizza il regime motore massimo
raggiunto attivando eventualmente
le spie di cambiata con la consueta
logica.
Per resettare le rilevazioni
cronometriche, si deve premere il
tasto Dx per almeno 5 secondi.
L'uscita dalla funzione “Lap Time
Memory” avviene quando si porta la
chiave in posizione “OFF”.
Funzione tensione batteria
Il cruscotto misura la tensione batteria
visualizzandola nel riquadro in basso a
destra del display LCD. Per leggere il
valore, si deve premere il tasto Dx fino
alla comparsa della scritta “VBATT”.
Gli estremi di visualizzazione sono
10 e 16 Volt: se il dato è compreso tra
10 e 12 Volt oppure tra 15 e 16 Volt,
l'indicazione lampeggia per segnalare
che la tensione della batteria è oltre il
campo ottimale di funzionamento. Se
la tensione rilevata è uguale o inferiore
a 9,9 Volt, compare la scritta “LO”
lampeggiante, mentre, se la tensione
è superiore o uguale a 16,1 Volt,
compare la scritta “HI” lampeggiante.
Durante la fase di trascinamento del
motore, la soglia per la comparsa della
scritta “LO” viene spostata a 8.5 volt
in modo da tenere conto dell'elevata
caduta di tensione dovuta
all'assorbimento del motorino di
avviamento: in questo modo si
evitano falsi allarmi sulla lettura
della tensione batteria.
Quando il cruscotto rileva una tensione
batteria anomala, si porta in modalità
di allarme e provvede a commutare
la lettura del display sulla funzione
“VBATT”. Se durante l'allarme viene
premuto il pulsante Dx, viene
visualizzata la nuova grandezza
per 10 secondi per poi tornare a
visualizzare l'allarme. Al termine
dell'anomalia, il cruscotto riprende la
modalità di funzionamento normale.
Lap Time Memory function
The recorded lap times can be
displayed when the motorcycle is
stationary and the engine is switched
off. To enter the Lap Time Memory
function, hold down the RH button
while turning the key to ON. Once the
display mode has been activated,
release the button: scroll through the
stored data by pressing the LH button.
The LCD will show the lap number,
time and maximum speed per lap.
The rev counter displays the
maximum engine speed; the gear
change lights will also operate
according to their usual logic.
To reset the recorded lap times,
hold down the RH button for more
than 5 seconds.
To exit the Lap Time Memory
function, turn the key to OFF.
Battery voltage
The instrument panel displays the
battery voltage in the box at the
bottom RH corner of the LCD. To read
the value, hold down the RH button
until the VBATT symbol appears.
The display limits are 10 and 16 volts:
if the battery voltage is between
10 and 12 Volts or between 15 to
16 Volts, the value flashes to indicate
that the battery voltage is outside the
optimal operating range. If the voltage
is less than or equal to 9.9 Volts, a
flashing LO symbol appears, while if it
is greater than or equal to 16.1 Volts,
a flashing HI symbol appears.
When the engine is being started, the
lower threshold for the “LO” symbol
shifts to 8.5 volts so as to take
account of the voltage drop caused
by the current drawn by ther starter
motor as it turns the engine over: this
avoids misleading alarm warnings
on the battery voltage readout.
When the instrument panel reads an
anomalous battery voltage, it moves to
alarm mode and switches the display
automatically to the VBATT indication.
If the RH button is pressed during the
alarm condition, the new reading is
displayed for 10 seconds, after which
the alarm is again displayed. At the end
of the malfunction, the instrument
panel returns to normal operation.
`
STATO 1
STATUS 1
STATO 2
STATUS 2
STATO 3
STATUS 3
VISUALIZZAZIONE
" LO "
LAMPEGGIANTE /
"LO" FLASHING
VISUALIZZAZIONE
" HI "
LAMPEGGIANTE /
"HI" FLASHING
VISUALIZZAZIONE
LAMPEGGIANTE /
FLASHING
VISUALIZZAZIONE FISSO /
DISPLAYED
VISUALIZZAZIONE LAMPEGGIANTE /
FLASHING
0.0
9.9
10
12.1
12
14.9
15
16.1
16
VOLT
Summary of Contents for 749DARK
