Danfoss VLT AutomationDrive FC 302, Programming Manual, Page: 169 / 346

13-01 Start Event
Select the boolean (true or false) input to activate smart logic
control.
Option: Function:
[4] On reference The motor runs on reference.
[5] Torque limit The torque limit set in
parameter 4-16 Torque Limit Motor Mode
or parameter 4-17 Torque Limit Generator
Mode is exceeded.
[6] Current Limit The motor current limit set in
parameter 4-18 Current Limit is exceeded.
[7] Out of current
range The motor current is outside the range
set in
parameter 4-18 Current Limit .
[8] Below I low The motor current is lower than set in
parameter 4-50 Warning Current Low .
[9] Above I high The motor current is higher than set in
parameter 4-51 Warning Current High .
[10] Out of speed
range The speed is outside the range set in
parameter 4-52 Warning Speed Low and
parameter 4-53 Warning Speed High .
[11] Below speed
low The output speed is lower than the
setting in
parameter 4-52 Warning Speed
Low .
[12] Above speed
high The output speed is higher than the
setting in
parameter 4-53 Warning Speed
High .
[13] Out of feedb.
range The feedback is outside the range set in
parameter 4-56 Warning Feedback Low
and
parameter 4-57 Warning Feedback
High
.
[14] Below feedb.
low The feedback is below the limit set in
parameter 4-56 Warning Feedback Low .
[15] Above feedb.
high The feedback is above the limit set in
parameter 4-57 Warning Feedback High .
[16] Thermal
warning The thermal warning turns on when the
temperature exceeds the limit in the
motor, the frequency converter, the
brake resistor, or the thermistor.
[17] Mains out of
range The mains voltage is outside the
specified voltage range.
[18] Reversing The output is high when the frequency
converter is running counterclockwise
(the logical product of the status bits
running AND reverse).
[19] Warning A warning is active.
[20] Alarm (trip) A (trip) alarm is active.
[21] Alarm (trip lock) A (trip lock) alarm is active.
[22] Comparator 0 Use the result of comparator 0.
[23] Comparator 1 Use the result of comparator 1.
13-01 Start Event
Select the boolean (true or false) input to activate smart logic
control.
Option: Function:
[24] Comparator 2 Use the result of comparator 2.
[25] Comparator 3 Use the result of comparator 3.
[26] Logic rule 0 Use the result of logic rule 0.
[27] Logic rule 1 Use the result of logic rule 1.
[28] Logic rule 2 Use the result of logic rule 2.
[29] Logic rule 3 Use the result of logic rule 3.
[33] Digital input
DI18 Use the result of digital input 18.
[34] Digital input
DI19 Use the result of digital input 19.
[35] Digital input
DI27 Use the result of digital input 27.
[36] Digital input
DI29 Use the result of digital input 29.
[37] Digital input
DI32 Use the result of digital input 32.
[38] Digital input
DI33 Use the result of digital input 33.
[39] Start command A start command is issued.
[40] Drive stopped A stop command (jog, stop, quick stop,
coast) is issued – and not from the SLC
itself.
[41] Reset Trip A reset is issued.
[42] Auto-reset Trip An auto reset is performed.
[43] Ok key [OK] is pressed. Only available on the
graphical LCP.
[44] Reset key [Reset] is pressed. Only available on the
graphical LCP.
[45] Left key [
◄
] is pressed. Only available on the
graphical LCP.
[46] Right key [
►
] is pressed. Only available on the
graphical LCP.
[47] Up key
[
▲
] is pressed. Only available on the
graphical LCP.
[48] Down key
[
▼
] is pressed. Only available on the
graphical LCP.
[50] Comparator 4 Use the result of comparator 4.
[51] Comparator 5 Use the result of comparator 5.
[60] Logic rule 4 Use the result of logic rule 4.
[61] Logic rule 5 Use the result of logic rule 5.
[76] Digital input
x30/2
Use the value of x30/2 (VLT
®
General
Purpose I/O MCB 101).
Parameter Descriptions Programming Guide
MG33MP02 Danfoss A/S © 10/2018 All rights reserved. 167
3 3