Danfoss VLT AutomationDrive FC 302, Programming Manual, Page: 315 / 346

17-6* Monitoring and App.
17-60 Feedback Direction [0] Clockwise All set-ups FALSE - Uint8
17-61 Feedback Signal Monitoring [1] Warning All set-ups TRUE - Uint8
17-7* Position Scaling
17-70 Position Unit [0] pu All set-ups TRUE - Uint8
17-71 Position Unit Scale 0 N/A All set-ups FALSE 0 Int8
17-72 Position Unit Numerator 1024 N/A All set-ups FALSE 0 Int32
17-73 Position Unit Denominator 1 N/A All set-ups FALSE 0 Int32
17-74 Position Offset 0 N/A All set-ups FALSE 0 Int32
17-75 Position Recovery at Power-up [0] Off All set-ups TRUE - Uint8
17-76 Position Axis Mode [0] Linear Axis All set-ups TRUE - Uint8
17-77 Position Feedback Mode [0] Relative All set-ups TRUE - Uint8
17-78 Active Position Counter [0] Counter 0 All set-ups FALSE - Uint8
17-8* Position Homing
17-80 Homing Function [0] No Homing All set-ups TRUE - Uint8
17-81 Home Sync Function [0] 1st time after power All set-ups TRUE - Uint8
17-82 Home Position 0 N/A All set-ups TRUE 0 Int32
17-83 Homing Speed 150 RPM All set-ups TRUE 67 Int16
17-84 Homing Torque Limit 160 % All set-ups TRUE 0 Uint16
17-85 Homing Timout 60.0 s All set-ups TRUE -1 Uint16
17-86 Homing Flag Behavior [0] Clear at Powerup All set-ups FALSE - Uint8
17-9* Position Config
17-90 Absolute Position Mode [0] Standard All set-ups TRUE - Uint8
17-91 Relative Position Mode [0] Target Position All set-ups TRUE - Uint8
17-92 Position Control Selection [0] No Operation All set-ups TRUE - Uint8
17-93 Master Offset Selection [0] Absolute Enabled All set-ups TRUE - Uint8
17-94 Rotary Absolute Direction [0] Shortest All set-ups TRUE - Uint8
5.3.18 18-** Data Readouts 2
Par.
No. # Parameter description Default value 4-set-up FC 302
only
Change
during
operation
Conver-
sion index
Type
18-0* Maintenance Log
18-00 Maintenance Log: Item 0 N/A All set-ups x FALSE 0 Uint8
18-01 Maintenance Log: Action 0 N/A All set-ups x FALSE 0 Uint8
18-02 Maintenance Log: Time 0 s All set-ups x FALSE 0 Uint32
18-03 Maintenance Log: Date and Time ExpressionLimit All set-ups x FALSE 0
TimeO
fDay
18-2* Motor Readouts
18-27 Safe Opt. Est. Speed 0 RPM All set-ups TRUE 67 Int32
18-28 Safe Opt. Meas. Speed 0 RPM All set-ups TRUE 67 Int32
18-29 Safe Opt. Speed Error 0 RPM All set-ups TRUE 67 Int32
18-3* Analog Readouts
18-36 Analog Input X48/2 [mA] 0 N/A All set-ups TRUE -3 Int32
18-37 Temp. Input X48/4 0 N/A All set-ups TRUE 0 Int16
18-38 Temp. Input X48/7 0 N/A All set-ups TRUE 0 Int16
18-39 Temp. Input X48/10 0 N/A All set-ups TRUE 0 Int16
18-4* PGIO Data Readouts
18-43 Analog Out X49/7 0 N/A All set-ups FALSE -3 Int16
18-44 Analog Out X49/9 0 N/A All set-ups FALSE -3 Int16
18-45 Analog Out X49/11 0 N/A All set-ups FALSE -3 Int16
18-5* Active Alarms/Warnings
18-55 Active Alarm Numbers 0 N/A All set-ups TRUE 0 Uint16
18-56 Active Warning Numbers 0 N/A All set-ups TRUE 0 Uint16
Parameter Lists Programming Guide
MG33MP02 Danfoss A/S © 10/2018 All rights reserved. 313
5 5