AGAC_0103
Spostare l’attrezzatura del terzo punto sui fori (1)
o (3) se:
• L’attività del sollevatore è eccessiva od irregolare
durante il comando dello sforzo.
• La parte posteriore dell’attrezzatura si alza troppo
quando viene sollevata. La posizione più bassa
offre la massima altezza di sollevamento ma una
forza minore, ed è consigliata quando si lavora con
l’aratro.
• La gamma della leva di comando sforzo è troppo
ridotta.
Spostare l’attrezzatura del terzo punto sui fori (1)
o (2) se:
• Il sollevatore reagisce ai comandi dello sforzo
in modo insoddisfacente ed il regime motore
scende eccessivamente prima del sollevamento
dell’attrezzatura.
• La parte posteriore dell’attrezzatura si abbassa
o viene trascinata al suolo quando l’attrezzatura
viene sollevata.
Abbassare l’attrezzatura per togliere il peso dall’attacco.
Move 3rd point implement onto holes (1) or (3) if:
•
Lift activity is excessive or erratic with draft control.
•
Implement rear end raises too much when being
lifted. The lowest position offers maximum lifting
height but a smaller force, and is recommended
when working with a plough.
•
Set draft control lever range is too small.
Move 3rd point implement onto holes (1) or (2) if:
•
The lift unsatisfactorily responds to draft controls
and engine rpm drops too much before lifting the
equipment.
•
Equipment rear end lowers or is dragged on the
ground when equipment is lifted.
Lower equipment down to remove weight from hitch.
pag. 71
5
revision 2 date: 07/19 doc. AG475426
Speciali
Livellamento dell’attacco
ATTENZIONE: attenersi alle dimensioni
specificate.
La lunghezza del terzo punto può essere regolata per
dare all’attrezzo un’angolazione adeguata rispetto
al livello del suolo. Accorciando la barra superiore
aumenta l’angolo con il terreno, mentre allungandola
diminuisce.
Di norma, con le barre inferiori in posizione orizzontale,
la parte posteriore della barra superiore dovrebbe
inclinarsi verso l’alto. Il fissaggio del terzo punto sul
trattore può essere eseguito in tre punti diversi.
Levelling hitch
CAUTION: comply with specified
dimensions.
Adjusting implement tilt angle with respect to the
ground is accomplished by adjusting the length of the
third-point. Shorten the upper link to increase tilt angle,
or lengthen it to decrease it.
Usually, with bottom links in horizontal position, the
upper link rear end should tilt upward. The fixing of
the third point on the tractor can be performed in three
different positions.
Summary of Contents for Agricube
