Agilent Technologies EasyEXPERT, Manual, Page: 470 / 610

Share

Page: 470 / 610

Agilent Technologies EasyEXPERT Manual Download Page 470

17 Utility

17.6

ForcePGC: PG Output1 Continuous Output (A.01.20)

[Supported Analyzer]
  B1500A, B1505A, 4155B, 4155C, 4156B, 4156C

[Description]
  Sets Output1 of Agilent 81110A Pulse Generator, and triggers continuous pulse output. Pulse leading/trailing
edge transition time can be set.
  Execute ResetPG to stop pulse output before the specified pulses are applied.

[Required Modules and Accessories]
  Agilent 81110A Pulse Generator (2-output, PGU1 and PGU2)
  GPIB cable

[Test Parameters]
  Address: GPIB address of Agilent 81110A Pulse Generator
  Period1: Pulse period [s]
  Delay1: Pulse delay time [s]
  Dcyc1: Duty cycle [%]
  LeadTime1: Pulse leading edge transition time [s]
  TrailTime1: Pulse trailing edge transition time [s]
  Level1: Pulse High level [V]
  Base1: Pulse Low level [V]
  ExtImp1: Load impedance [ohm]

Agilent EasyEXPERT Application Library Reference, Edition 8

17-8

«
...
468
469
470
471
472
...
»

Summary of Contents for EasyEXPERT



































































































































































































































































































































































































































































































































































































































Reviews:

No comments