Volvo EC60E Скачать руководство пользователя страница 96

Страница: 96 / 342

6) Source change button

By pressing the FM/AM button, the radio starts and

radio modes change (RADIO/USB/AUX).

By pressing this button, you can change the source

of music played by the audio system. When you

press this button in Bluetooth mode, it changes into

Connected Audio Control Mode.
7) Call button (optional equipment)

Press Bluetooth (connected audio control mode)

button for actions related to calls, including calling/

hanging up/answering/rejecting.

When the phone rings, this button flashes green,

and during a conversation, the light is on with fixed

green.

- Not calling: Calling

- In calling: Hanging-up

- Flashing (phone ringing): Answering

- Keep pressing the button while flashing:

Rejecting

- Call function of the button above calls the

previous number

8) Bluetooth button (optional equipment)

By pressing this button, the following functions will

work according to the machine's Bluetooth

connection status.

- Not connected: Requesting connection to the

previously connected device

- Connected: Change to Bluetooth mode

- Keep pressing the button when connected:

Disconnect Bluetooth

9) Call mic (optional equipment)

When you talk using a hands-free device, you can

transmit a voice with this mic.

Instrument panels

Instrument panel, right

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 96 / 342

Результаты поиска

Содержание EC60E

Отзывы: