Volvo EC60E Скачать руководство пользователя страница 131

Страница: 131 / 342

Bluetooth

You can connect the audio sound system via

Blue-tooth® with other Bluetooth® ready devices,

such as cell phones or MP3 players. This allows

you to use the audio sound system with its

integrates microphone as hands-free system for

connected cell phones and control the audio

output of other Bluetooth® devices and play them

back via the loudspeakers of the audio sound

system (Bluetooth® streaming).

Bluetooth® technology is a wireless connection

of short range. For this reason, Bluetooth®

devices must be located near the audio sound

system (in the machine) to establish and maintain

a connection.

To establish a Bluetooth® connection, you must

first pair the audio sound system and the

Bluetooth device. When you pair the devices, a

Bluetooth® connection is subsequently

established automatically. This connection

remains in effect as long as the Bluetooth device

is within range. if the connection is interrupted the

connection is automatically re-established as

soon as you are back within range.

130

Other controls

Operator comfort

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 131 / 342

Результаты поиска

Содержание EC60E

Отзывы: