Volvo EC60E Скачать руководство пользователя страница 169

Страница: 169 / 342

Transporting the machine

NOTICE

Select low engine speed and low travelling speed

for loading and unloading the machine.
NOTE!

Make sure that loading ramps and platforms are

free from oil, mud, ice and similar so that the

machine does not begin to slip.
NOTE!

When the dozer plate is in the rear position (180

degree rotation), the travel system operation is

reversed. Take care when operating with the dozer

blade at the rear.

1 Place the trailer on a firm and level ground.

2 Apply the brake of the trailer.

3 Insert blocks in front of and behind the tyres of

trailer.

4 Fix loading ramp securely.

- Make sure that the strength, width, length and

thickness of the planks are safe for loading.

- Make sure that the angle of loading ramp is 15°

or less.

5 Align the machine's tracks to the ramp, the dozer

blade to the rear (to serve as a support in case

of an operating error) and the attachments to the

front position (A).

6 Drive to the end of the ramp, extend the

attachments to position (B), so that the machine

tips on to the loading platform of the trailer.

Lower the excavating equipment and the dozer

blade to the loading platform.

V1158797

168

Operating instructions

Transporting machine

Содержание EC60E























































































































































































































































































































































Результаты поиска

Содержание EC60E

Отзывы:

Volvo EC60E, Руководство оператора, Страница: 169 / 342

Результаты поиска

Содержание EC60E

Отзывы: